How to Fix the VSC Light Problem
Here are the detailed steps to fix the VSC light problem:
1. Read the Error Codes
Because there are a wide variety of issues that can cause the VSC light, you should always scan for trouble codes in the engine control module, ABS control module, and other related control modules before doing anything else.
Modern cars have advanced diagnostic software that can diagnose and let you know if there is a problem with the engine or ABS sensors. This is handy because it means that if something goes wrong, you don’t have to measure and diagnose every sensor in the car. This information can be read with an OBD2 scanner. You can use almost any scanner on the market to read the engine control unit. However, you may need a vehicle-specific scanner to read the ABS control unit.
If you can’t find a problem with the engine control module, you can try reading the codes with an inexpensive scanner or go to an auto repair shop to have the ABS codes read.
2. Check the brake lights
The brake light switch is a common part that can cause the VSC light to come on. So, checking your brake lights is a quick and easy solution.
With the ignition on, have a friend or family member step on the brake pedal to see if your brake lights are working. Unfortunately, some brake light switches use two different currents, so even if your brake lights are working, there could be a problem with the switch. However, if your car doesn’t have brake lights, you should take a closer look at your brake light switch.
3. Check your fuel cap.
A common cause of the VSC light coming on in Lexus and Toyota along with the TRAC OFF light and check engine light is a leaking or loose gas cap. If the VSC light comes on after refueling, make sure your fuel cap is properly tightened.
This can also happen if you leave your car running with the gas cap open while refueling. In this case, you may be able to fix the VSC light simply by clearing the code memory. However, you should check the O-ring on your tank cap to make sure it seals properly and isn’t leaking.
4. Check the brake fluid level
Another easy solution is to check the brake fluid level. A low brake fluid level can cause various problems with the ABS system and can also lead to failure of the VSC system.
So, check your brake fluid reservoir and make sure the level is not too low. If it is very low, you should check for brake fluid leaks around the brakes and refill the reservoir.
5. Consult a Professional
If you have tried all of the above and still can’t find the cause of the problem, it’s a good idea to seek help from a professional. Taking your car to a repair shop to have the problem diagnosed can be costly. However, many mechanics have dealt with the same problem many times before, so they may be able to solve it quickly.
How do I reset the VSC light? Traction Control Off
There’s a simple solution: reset your VSC light. Most likely your VSC light is on due to an intermittent issue. To reset your VSC light, try these steps:
>> Stop your car and put it in Park.
>> Locate the VSC button. It’s usually near the gear shift, but on some cars it may be next to or behind the steering wheel.
>> Press and hold the VSC button for a few seconds.
>> The TRAC OFF and VSC OFF indicator lights will come on. Both the traction and VSC systems are now off.
>> Press the VSC button again for one second. Both the TRAC and VSC lights will turn off and the systems will restart. If the problem still persists, you need to check the error code and perform a real diagnosis to find the problem. If you don’t have the skills to repair it yourself, take your car to a repair shop.
Where is the VSC button?
For Toyota and Lexus, the VSC button is usually located on the left side under the steering wheel, or near the gear shift lever. Some cars have the word “VSC” on the button, while some models only have a symbol of a skidding car. Can I drive with the VSC light on? Generally, it is safe to drive with the VSC light on, and your car will run fine if you drive carefully. However, you should be extra careful because it will disable your car’s traction control system. Therefore, we recommend that you fix the problem as soon as possible.
How do I turn off the VSC light?
You may be able to reset the VSC light by pressing the VSC button to disconnect and re-enable the VSC system. However, you may need an OBD2 scanner to do this, and in most cases, there is a problem that needs to be fixed before you can clear the code.
The VSC system works in conjunction with many other systems in your vehicle, so a variety of issues can cause the VSC light to turn on. Therefore, it is especially important to start your diagnosis in the right place and read codes for all control modules.
We hope this article was helpful to you. If you read this article to the end, you should have the knowledge to fix the VSC light on your dashboard. Don’t forget to subscribe to our YouTube channel!
